ORBINOX, present in more than 70 countries, has over 40 years of experience designing, manufacturing and distributing knife gate valves, penstocks, dampers and valves for hydraulic works ORBINOX have a highly qualified and experienced staff able to offer the most comprehensive solutions to our customers needs.Thanks to the worldwide sales network in 5 continents, we are near you to offer technical advice and respond to your needs. Solving your most demanding valve applications is our goal.

The manufacturing plants are equipped with the most up to date machinery due to the commitment to continuous investment and improvement. This allows us to achieve great flexibility when serving our customers. The Quality Assurance System covers all steps (from design to final testing), is in accordance to ISO 9001 and is certified by Lloyd’s Register Quality Assurance since 1994.

Nowadays, ORBINOX is one of the world’s leading producers of Knife Gate Valves.

This success is a result of our commitment to quality and service for the benefit of our customers. The Quality Management System of ORBINOX, S.A. has been approved by Lloyd’s Register Quality Assurance to ISO 9001:2000 after a successful renewal audit.

Wafer Knife Gate Valve
The EX model knife gate is a uni-directional wafer valve designed for general industrial service applications. The design of the body and seat assures non-clogging shutoff on suspended solids in industries such as :
• Pulp and Paper
• Power plants
• Wastewater treatment plants
• Chemical plant
• Food and Beverage
• Bulk handling
• Mining etc

Sizes :
DN 50 to DN 1200 (larger diameters on request)


Single Wedge Knife Gate Valve
A rugged cast body and bonnet combined with a shut-off system based on half-wedges on the body and gate means the knife gate valve offers the highest performance in terms of seal (both valve seat and to atmosphere) and of working pressures as well.
For use with heavy or hazardous fluids and high working pressures, in the chemical or food industry (reactors,…) as well as in the environmental sector (pumping of waste waters, sludge).

Sizes:
DN 80 (3”) to 1000 mm (40”)
Working pressure up to 64 bar, depending on size
Actuators: Hand wheel, Pneumatic, Electric or Hydraulic


Knife Gate Valve acc. to MSS SP81
The ET model knife gate is a uni-directional lug type valve designed according to MSS-SP-81 and TAPPI-TIS 405 for industrial service applications.
The design of the body and seat assures non-clogging shutoff on suspended solids in industries such as :
• Pulp and paper
• Power plants
• Mining
• Chemical Plants
• Wastewater
• Food and Beverage etc.

Sizes:
2” to 30” (larger diameters on request)


Through Conduit Knife Gate Valve
The TL model knife gate is through conduit wafer valve designed for media with high consistency. The double seat design assures a non-clogging shut off on either normal or reverse flow. The valve is used in a wide range of demanding applications in industries such as:
• Pulp & Paper
• Wastewater Treatment Plants
• Power Plants
• Chemical Plants etc.

Sizes:
DN 50 to DN 600 (larger diameters on request)


Round & Square Port knife Gate Valve
The CR model knife gate is a heavy duty valve designed for handling difficult applications. This valve suitable for us in recycle applications, like junk or sand traps of pulpers, high consistency cleaners…or as silo outlet with solid material.
The two piece body with round inlet and square outlet (larger than the inlet) assures non-jamming.

Sizes:
DN 100 to DN 600 (larger diameters on request)


Double Gate Knife Gate Valve
The DT model knife gate is double gate valve widely used in the Pulp and Paper industry (recycling or secondary fibre processing) designed to handle high concentrated or contaminated media. In open position, both gates retract into the body and allow full flow. When closing, the gates push stock and contaminants as staples, wires…..out of the body into the flow.
All components subject to wear are replaceable.

Sizes: DN 100 to DN 600 (larger diameters on request)


Bidirectional Knife Gate Valve
The EB model knife gate is bi-directional valve designed for general industrial service applications. The design of the body and seat assures non-clogging shutoff on suspended solids in industries such as:
• Wastewater treatment plants
• Chemical plants
• Food and Beverage etc.

Sizes:
DN 50 to DN 1200 (larger diameters on request)


Rubber Sleeve Knife Gate Valve
The VG model knife gate is a wafer valve designed for a wide range of industrial applications. The double-seated design provides bi-directional shut off. The design of the valve body and the two rubber sleeves makes the VG valve suited for use in handling abrasive slurries in industries such as:
• Mining
• Power plants
• Chemical plants
• Wastewater treatment etc.

Sizes:
DN 50 to DN 600 (large DN on request)


Hopper Shape Knife Gate Valve
The XC model knife gate is a wafer valve designed for industrial bulk handling service applications (powered and granular products). The special design of the body allows for easy passage of the fluid and makes it ideal for use as silo outlet valve. Widely used in industries such as:
• Power plants
• Food and Beverage
• Chemical plants
• Mining etc.
The valve is normally installed in the reverse position (seat upstream) in order to avoid problems like build-up in valve body, seat wear, difficult closing….

Sizes:
DN 50 to 600 (larger diameters on request)


Square Port Knife Gate Valve
The BC model knife gate is a square port low-pressure valve for solid loaded fluids, mainly used in bulk handling and silo outlet applications in industries such as:
• Chemical plants
• Wastewater treatment plants
• Power plants
• Mining
• Food and Beverage etc.

Sizes:
From DN 150 x 150 to DN 600 x 600 (other dimensions on request)


Tilting Disc Check Valve
The RM model check valve is a reliable metal seated non-return valve with oblique seating angle widely used in industries such as:
• Pulp and Paper
• Wastewater treatment plants
• Food and Beverage etc.

Main features:
-Suitable for all the standard flanges
-Short Face to Face
-Excellent tightness according to API 598
-Low pressure drop and opening pressure
-Quick closing reaction (oblique seating)
which reduces water hammer
-As an option auxiliary spring increases the closing reaction

Sizes:
DN 40 to DN 900 (larger DN on request)

The Indian facility at Coimbatore started operation in 2004 and exported its complete production to Europe and USA for one year. After increasing the capacity in 2005 ORBINOX, India launched its products in Indian Market. Within one year of launch, ORBINOX, INDIA has developed many reputed clientele like West Coast Paper Mills, Ballarpur Industries ltd. Sterilite Industries Ltd, Emami paper Mills, Century Pulp and Papers, Yash Papers etc.